ZEN27 S2 Dimmer & Compatible Hubs
## Will the S2 Dimmer ZEN27 work with my hub? The dimmer works great with the following Z-Wave systems: * **[Z-Box Hub][1] (recommended for all Zooz products)** * 2GIG (no advanced settings or scene control available) * ADT Pulse (no advanced settings or scene control available) * Alarm.com (no advanced sett…
Zooz SmartThings Edge Drivers
SmartThings is slowly transitioning from the legacy groovy platform to the [new lua platform][1]. This creates new challenges for seamless integration as well as access to key and advanced features of our devices. As usual, we're committed to providing the best possible experience to all of our customers, regardless o…
How to Add Your ZEN27 Dimmer to SmartThings
## Before moving on to Z-Wave set up, check that your dimmer works at 100% manually. Once you verify that it works well locally, it's time to add the dimmer to SmartThings. The switch will work with the out of the box; however, we recommend[ installing the lua Edge driver][1] first to provide access to all the advanc…
ZEN27 S2 Dimmer Specs
**Here are the technical details for the S2 Dimmer ZEN27:** * **Z-Wave Signal Frequency:** 908.42 MHz * **Power:** 120 V, 60 Hz * **Maximum Load:** 100 W LED, 300 W incandescent (200 W with one side of heat sink tabs off, 100 W with both sides of tabs off) * **Range:** Up to 100 feet line of sight * **Insta…
Can My Zooz Switch Be Used with Add-Ons, Dimmers, or Another Z-Wave Switch?
## While Zooz switches cannot be directly wired to other smart switches or electronic add-on switches, you can make two Zooz switches work together using remote Z-Wave control. Remember, always wire your Zooz switches according to the appropriate diagram from the manual for the model you're installing. Zooz switches …
Minimum Load Requirement - Why It's There
## Why is there a 15W / 20W minimum load required for some of our dimmers? Our recommendation is to have at least 15 Watts of load connected to your Zooz ZEN22, ZEN24, ZEN72, ZEN74, and ZEN77 VER 3.0/4.0 dimmers even though chances are the switch will work just fine with a single LED bulb as well. It's quite random h…
How Do I Perform Hard Reset on My ZEN27 Dimmer?
## Hard reset can help with a variety of configuration issues. It's also a good idea to try reset if your dimmer is unresponsive to Z-Wave commands, especially if you already gave [exclusion][1] a try without any luck. **Tap-tap-tap’n’hold the upper paddle for 10 seconds or more** to reset the dimmer. The LED indica…
ZEN27 S2 Dimmer VER. 3.01 Advanced Settings
## Here is a full list of advanced settings (parameters) for ZEN27 S2 Dimmer VER. 3.01 firmware: ### _On/Off Paddle Orientation_ **Parameter 1: **Choose if you want the upper paddle to turn the light on or turn the light off when tapped. **Values: **0 – Upper paddle turns the light on, lower paddle turns it off (de…
ZEN2X vs ZEN7X Models: What's the Difference
## You may have noticed our Zooz light switches line has expanded. We just love updating and upgrading products for you! So what's the difference between the new 700 series switches and the 500 series models? **Here is a short list of upgrades we implemented in the 700 series models:** * **700 series Z-Wave chip*…
How to Access Advanced Settings for My ZEN27 Dimmer on SmartThings
## With the latest transition to the [lua platform][1], SmartThings will no longer support groovy-based device handlers. Don't worry, we've created a new custom Edge driver for the ZEN27 Switch for the lua platform! Below are the instructions on how to install the new Edge driver. If you haven't added one before, jus…
