How to Perform an OTA Firmware Update on Zooz Devices on HomeSeer
You can check out the steps below for more information on how to update your Zooz end devices via HomeSeer. * Make sure you've already downloaded the correct firmware for the device you're updating, have extracted it from the .zip file, and know where it's located on your computer * From the HomeSeer main menu, cl…
ZEN06 Smart Plug Change Log
This is product is discontinued and replaced with ZEN04 . What does that mean? Here is a list of updates we made to the ZEN06 model so far. VER. 1.0 (released 10/2016) Original release. Hardware: * Power monitoring, 2 USB ports (no Z-Wave control or reports), smart LED ring Firmware: 1.01 * Overload protec…
ZEN24 Toggle Dimmer Change Log
This is product is discontinued and replaced with the ZEN74 . What does that mean? Here are the changes and updates we made to the ZEN24 model so far. VER. 1.0 (released 12/2016) Original release. Hardware: * Did NOT include neutral jumper * Implemented the classic 3-way functionality with a dedicated add-o…
My Z-Wave Stick Was Bricked During a Firmware Update
Updating your Z-Wave stick needs to be done only if necessary and exactly according to the instructions for the model and version you have. If your Z-Wave stick is working well, do not attempt a firmware update for it. This is a static controller with a crucial function to your network. Only perform the update when y…
ZEN23 Toggle Switch Change Log
This is product is discontinued and replaced with ZEN73 . What does that mean? Here's where you'll find the changes and updates we made to the ZEN23 switch model so far. VER. 1.0 (released 6/2016) Original release. Hardware: * Did NOT include neutral jumper or short screws for wall plate * Implemented the c…
ZAC36 Valve Actuator Change Log
Here is a list of the changes and updates we made to the ZAC36 Titan Water Valve Actuator so far. VER. 1.0 (released 8/2021) Original release. Hardware: * 700 Series Z-Wave chip * Smart auto-calibration process * IP 66 outdoor rating * Included 4.75' water leak probe * Installation Requirements: 0.5" - 1.25…
ZSE19 S2 MultiSiren Change Log
This is product is discontinued and has been replaced by the ZSE50 Siren & Chime : What does that mean? Documentation for the new ZSE50 Siren & Chime can be found here: ZSE50 Knowledge Base Here are the updates we applied to the ZSE19 model so far. VER. 1.0 (released 11/2018) Original release. Hardware: …
ZSE40 700 4-in-1 Sensor Change Log
This is product is discontinued and replaced with ZSE11 . What does that mean? Here are the features we added to the 4-in-1 Sensor so far. VER. 1.0 (released 9/2016) Hardware: * 2 x AAA batteries * Mounting bracket included * 500 Series Z-Wave chip Firmware: 16.09 * 4 LED indicator modes * 12h wake-up int…
ZEN51 Dry Contact Relay Change Log
Here is a list of the changes and updates we made to the ZEN51 Dry Contact Relay so far. VER. 1.0 (released 1/2022) Original release. Hardware: * 700 Series Z-Wave chip * Single pole or direct 3-way capability * Pigtail wires for easy installation * Wiring limitation: in certain scenarios with too much noise…
How to Perform an OTA Firmware Update on Zooz Devices on Hubitat
Hubitat has firmware update options available for C-5, C-7 and C-8. If you're on Hubitat C-7 or C-8, the community developer Bryan Copeland created a tool to update Z-Wave devices over the air straight from the hub. Click here to learn more and remember to say thanks to Bryan in the forum thread if you end up usin…
