How to Access Advanced Settings for My ZEN53 DC Motor Controller on Hubitat
The ZEN53 DC Motor Controller should be integrated with Hubitat soon. In the meantime, please install the custom driver below to ensure the device can be recognized and configured correctly on the platform. All About Advanced Settings The terminology for advanced settings varies depending on your Z-Wave hub. For in…
Can't Add My ZSE43 Tilt|Shock XS Sensor to Hubitat
The ZSE43 XS Sensor is officially supported by Hubitat so it will work with the hub out of the box as long as the platform is on version 2.2.9 or higher. To help with the ZSE43 Sensor configuration, try the exclusion process first. This can be done even if it was never connected to the hub, as it acts as a soft rese…
My ZEN74 Toggle Dimmer is Offline in Hubitat
Range or configuration issues can make the ZEN74 appear as “offline” in Hubitat. You can try fixing the problem with a simple Z-Wave Repair. You’ll need to check if your Hubitat platform is up-to-date first. Then, you can give repairing your network connections a try. Follow these steps to run the repair in Hubit…
How to Use Your ZEN32 Scene Controller With Smart Bulbs On Hubitat
Use the ZEN32 Scene Controller to control smart bulbs on Hubitat for the ultimate automation flexibility. Remember that your smart bulbs need to be added to Hubitat so that you can turn them on and off and adjust colors from the Hubitat interface. In this article we go through the steps of programming the Scene Contr…
Can't Add My ZSE42 Water Leak XS Sensor to Hubitat
Having issues including the ZSE42 XS Sensor to Hubitat? Try excluding the sensor first. Please ensure the platform is running on version 2.2.9 or higher. 800 series only: Exclusion before inclusion applies to the 700 series and earlier chip sets. The 800 series devices will not exclude before they have been inclu…
My ZSE43 Tilt | Shock XS Sensor Shows Offline in Hubitat
If your ZSE43 is showing up as “offline” in Hubitat, it may point to a range or configuration problem. A Z-Wave Network Repair may be the answer! Check to see if your Hubitat hub is up to date on its platform version. Next, using the steps outlined below, run the Z-Wave Repair to refresh your Z-Wave mesh network con…
My ZEN51 Dry Contact Relay Shows Offline in Hubitat
If Hubitat shows your ZEN51 Dry Contact Relay as “offline," it may suggest a range or configuration issue. A Z-Wave Network Repair may be the solution! Ensure your Hubitat hub is up to date on its platform version. Next, utilize the steps below to run the Z-Wave Repair to refresh your Z-Wave mesh network connections…
Can't Add My ZEN74 Toggle Dimmer to Hubitat
Trouble getting the ZEN74 to pair? Try the exclusion process first! Excluding is a simple and effective process that acts as a soft reset to help with any inclusion and configuration issues. It can be done even if your ZEN74 was never successfully added to your Hubitat network. However, please note that exclusion be…
Can't Add My ZEN52 Double Relay to Hubitat
The ZEN52 Double Relay is fully supported by Hubitat so it will work with the hub out of the box! Ensure the platform is on version 2.2.9 or higher. To help with the ZEN52 Double Relay configuration, try the exclusion process first. This can be done even if it was never connected to the hub, as it acts as a soft re…
Can't Add My ZSE41 Open|Close XS Sensor to Hubitat
The ZSE41 XS Sensor is officially integrated with Hubitat, so it will work with the hub out of the box! Please ensure the platform is running on version 2.2.9 or higher. If you find you have an issue including the ZSE41 Sensor to Hubitat, please try the exclusion process first. This can be done even if it was never…
