-
Can't Add My ZAC36 Valve Actuator to Hubitat
Try excluding the ZAC36 from Hubitat before giving inclusion another try! You can remove any Z-Wave device, including the ZAC36, on the Hubitat app, even if it was never successfully included - the app should confirm an unknown device was removed. Just make sure you have the latest Hubitat verison installed. 800 …
-
How to Use Your ZEN34 Remote Switch With Smart Bulbs On Hubitat
If you're looking for a battery powered wall remote and you don't want to worry about wiring, the ZEN34 Remote Switch is a convenient choice. It fits in any standard electrical box or can be fixed to a wall or any flat surface for easy installation. Program the paddle on this device according to the standard scene co…
-
Can't Add My ZEN73 On/Off Toggle Switch to Hubitat
Not able to include the ZEN73 to Hubitat? It's time to try exclusion! Removing the switch from your hub is possible, even if it’s never been added. An “unknown” device will be excluded and you can then try to include it again. Just make sure your Hubitat is running on the latest version first. ZEN73 Exclusion Steps…
-
Can't Add My ZSE43 Tilt | Shock XS Sensor to Hubitat
While the ZSE41 XS Sensors is officially supported by Hubitat version 2.2.9 or higher, we recommend the custom driver for best user experience. To help with the ZSE43 Sensor configuration, try the exclusion process first. This can be done even if it was never connected to the hub, as it acts as a soft reset. ZSE4…
-
My ZEN14 Outdoor Double Plug Shows Offline in Hubitat
Range, interference, or configuration issues may be the root cause of your ZEN14 Outdoor Double Plug showing as “offline” in Hubitat. An easy place to start is with is Z-Wave Network Repair. Ensure your Hubitat platform version is up-to-date first. Next, use Z-Wave Repair to refresh your mesh connections. Follow the…
-
My ZSE44 Temperature | Humidity XS Sensor Shows Offline in Hubitat
A range or configuration problem may cause your ZSE44 to show up as “offline” in Hubitat. A Z-Wave Network Repair may be the answer! Check to see if your Hubitat hub is up to date on its platform version. Next, using the steps outlined below, run the Z-Wave Repair to refresh your Z-Wave mesh network connections: *…
-
My ZEN52 Double Relay Shows Offline in Hubitat
Does the ZEN52 Double Relay show as “offline" in Hubitat? This suggests a range or configuration issue. A Z-Wave Network Repair could help. Ensure your Hubitat hub is up to date on its platform version. Next, utilize the steps below to run the Z-Wave Repair to refresh your Z-Wave mesh network connections: * Open …
-
Can't Add My ZAC38 Range Extender to Hubitat
Can't include the ZAC38 Range Extender to Hubitat? Exclusion is the best place to start! Excluding the Range Extender from Hubitat may help with any connection or configuration issues. It can be done at any time, even if the device has never been added to the hub’s network. Before going through the removal process, …
-
My ZSE43 Tilt | Shock XS Sensor Shows Offline in Hubitat
If your ZSE43 is showing up as “offline” in Hubitat, it may point to a range or configuration problem. A Z-Wave Network Repair may be the answer! Check to see if your Hubitat hub is up to date on its platform version. Next, using the steps outlined below, run the Z-Wave Repair to refresh your Z-Wave mesh network con…
-
My ZSE41 Open | Close XS Sensor Shows Offline in Hubitat
A range or configuration issue could cause your ZSE41 Open|Close XS sensor to show up as “offline” in Hubitat. Try a Z-Wave Network Repair! Ensure your Hubitat hub is up to date on its platform version. Follow these steps to run the Z-Wave Repair to refresh your Z-Wave mesh network connections: * Open Hubitat …
Looking for Z-Box Hub Support? Please click here to access the Z-Box Hub Support Portal.
