Zooz On Off Toggle Switch ZEN23 VER. 3.05 Advanced Settings

Here is a full list of advanced settings (parameters) for Zooz ZEN23 VER. 3.05 firmware:

On/Off Toggle Orientation

Parameter 1: Choose if you want to turn the light on or turn the light off when you toggle the switch up.

Values: 0 – Toggle up to turn the light on, toggle down to turn it off (default); 1 – Toggle up to turn the light off, toggle down to turn it on; 2 – Toggle any direction to turn the light on/off (change state).

Size: 1 byte dec

Auto Turn-Off Timer

Parameter 3: Use this parameter to enable or disable the auto turn-off timer function.

Values: 0 – timer disabled (default); 1 – timer enabled.

Size: 1 byte dec

Parameter 4: Use this parameter to set the time after which you want the switch to automatically turn off once it has been turned on. The number entered as value corresponds to the number of minutes.

Values: 1 – 65535 (minutes). Default: 60.

Size: 4 byte dec

Auto Turn-On Timer

Parameter 5: Use this parameter to enable or disable the auto turn-on timer function.

Values: 0 – timer disabled (default); 1 – timer enabled.

Size: 1 byte dec

Parameter 6: Use this parameter to set the time after which you want the switch to automatically turn on once it has been turned off. The number entered as value corresponds to the number of minutes.

Values: 1 – 65535 (minutes). Default: 60.

Size: 4 byte dec

Association Reports

Parameter 7: Choose which physical and Z-Wave triggers should prompt the switch to send a status change report to associated devices.

Values: 0 – none; 1 – physical tap on ZEN26 only; 2 – physical tap on connected 3-way switch only; 3 – physical tap on ZEN26 or connected 3-way switch; 4 – Z-Wave command from hub; 5 – physical tap on ZEN26 or Z-Wave command from hub; 6 – physical tap on connected 3-way switch or Z-Wave command from hub; 7 – physical tap on ZEN26 / connected 3-way switch or Z-Wave command from hub; 8 – timer only; 9 – physical tap on ZEN26 or timer; 10 – physical tap on connected 3-way switch or timer; 11 – physical tap on ZEN26 / connected 3-way switch or timer; 12 – Z-Wave command from hub or timer; 13 – physical tap on ZEN26, Z-Wave command from hub, or timer; 14 – physical tap on ZEN26 / connected 3-way switch, Z-Wave command from hub, or timer; 12 – all of the above. Default: 15.

Size: 1 byte dec

On Off Status After Power Failure

Parameter 8: Set the on off status for the switch after power failure.

Values: 0 – forced to OFF (regardless of state prior to power outage); 1 – forced to ON (regardless of state prior to power outage); 2 – remembers and restores on/off status after power failure (default)

Size: 1 byte dec

Enable/Disable Scene Control

Parameter 9: Enable or disable scene control functionality for quick double tap triggers.

Values: 0 – scene control disabled (default). 1 – scene control enabled.

Size: 1 byte dec

Smart Bulb Mode: Enable/Disable Paddle / Z-Wave Control

Parameter 11: Enable or disable local on/off control. If enabled, you’ll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles.

Values: 0 – physical paddle control disabled. 1 – physical paddle control enabled (default). 2 – physical paddle and Z-Wave control disabled. NOTE: tap the upper paddle 10 times quickly to change this mode.

Size: 1 byte dec

Parameter 13: Set reporting behavior for disabled physical control.

Values: 0 – switch reports on/off status even if physical and Z-Wave control is disabled (default). 1 – switch doesn't report on/off status when physical (and Z-Wave) control is disabled.

Size: 1 byte dec

3-Way Switch Type

Parameter 12: Choose the type of 3-way switch you want to use with this dimmer in a 3-way set-up. Changing this setting can allow you to control brightness and dim the light from both 3-way locations. Use a regular momentary switch (like the Zooz ZAC99 accessory switch) if value is set to 2.

Values: 0 – regular mechanical 3-way on/off switch, use the connected 3-way switch to turn the light on or off (default); 1 – momentary switch, click once to change status (light on or off).

Size: 1 byte dec

MANUAL CONTROL

Toggle Up: 

1 x tap: load on; Scene 1, attribute 00 (button 1)

2 x tap: Scene 1, attribute 03 (button 3)

3 x tap: enter inclusion (pairing) mode; Scene 1, attribute 04 (button 5)

4 x tap: Scene 1, attribute 05 (button 7)

6 x tap: change LED indicator mode (see parameter 2)

10 x tap: change physical / Z-Wave control mode (see parameter 11)

tap-tap-tap-and-hold: factory reset

Toggle Down: 

1 x tap: load off; Scene 2, attribute 00 (button 2)

2 x tap: Scene 2, attribute 03 (button 4)

3 x tap: enter exclusion (unpairing) mode; Scene 2, attribute 04 (button 6)

4 x tap: Scene 2, attribute 05 (button 8)

tap-tap-tap-and-hold: factory reset

All ZEN23 VER. 3.0 switches can be updated via OTA firmware updates, here is how to do that. You can request a firmware update file here, please include your order number for verification!

  • 317
  • 01-Apr-2020
  • 203 Views