ZEN54 0-10V Dimmer Product Manual

Don't forget to register your product for extended warranty and more perks:

Click here to register your device here.

FEATURES

Z-Wave 0-10 V dimming control for LED fixtures
Great for 0-10 V LED drivers in LED panels
Smooth dimming with instant status updates
Installs behind your existing wall switch (on/off or momentary)
700 series Z-Wave chip for better range and faster control
Z-Wave Long Range for ultra reliable no-mesh communication
Advanced configuration including min and max brightness
Built-in Z-Wave signal repeater for boosted communication
SmartStart and S2 Security for a safer network

SPECIFICATIONS

Model Number: ZEN54 LR
Power Input: 100-240 VAC, 50/60 Hz, max. 4.1 A, 984 W
Power Output: 100-240 VAC, 50/60 Hz, max. 4 A, 960 W
Maximum Load: 4 A (use with 0-10 V LED drivers only)
Range: Up to 300 feet line of sight (or up to a mile with LR)
Operating Temperature: 32-104° F (0-40° C)
Installation and Use: Indoor only

CAUTION

This is an electrical device - please use caution when installing and operating the 0-10 V Dimmer. Remote control of appliances may result in unintentional or automated activation of power. Do not use this Z-Wave device to control electric heaters or other appliances which produce the risk of fire, burns, or electrical shock when unattended. To reduce risk of overheating and possible damage to other equipment, do not install this unit to control a receptacle; a motor-operated appliance; a fluorescent lighting fixture; any device over 32 V DC power; or a transformer-supplied fixture. Use with 0-10 V LED drivers only.

BEFORE YOU INSTALL: This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a licensed electrician perform this installation.

WIRING: READ IT!

Not sure what you're seeing? Send images of the fully working installation before you disconnect the wires to support.getzooz.com.

CHECK THE LOAD: don’t exceed 4 A for your 0-10 V Dimmer, USE ONLY WITH 0-10 V LED DRIVERS
POWER OFF: turn the circuit power off in the breaker panel before you start. If installing in a multi-switch box with multiple circuits, turn power off at all of the circuits.
CHECK THE WIRES: mark 0-10 V driver connections (GNDand 0-10 V+), power (L and N), load to LED driver (LOAD) and switch connections (SW and GND). Don’t rely exclusively on your multimeter to identify the wires!
DISCONNECT THE SWITCH: remove the wires between the switch and the LED driver and label them accordingly. 5. CONNECT THE 0-10 V DIMMER: follow all installation steps carefully. Wire the device EXACTLY like in the diagram. Depending on your set-up, you may need to install the device at the LED fxture rather than in the switch box.

NOTE: ON/OFF OR MOMENTARY SWITCHES ONLY. Do not connect the ZEN54 to a wall dimmer, illuminated switch, or electronic add-on switch. The ZEN54 device can only be wired with on/off or momentary wall switches. Physical dimming available from momentary switches only. With on/off switches, dim via Z-Wave only.

ZEN54 WIRING DIAGRAM FOR 0-10 V LED DRIVERS

Connect the driver wires to GND - and 0-10V+ on ZEN54.
Connect the wall switch to the GND- bundle and the SW pigtail on the ZEN54.
Connect the LOAD on the ZEN54 to the line input on the LED driver.
Connect neutral from the 120 V power source to N on ZEN54 and the neutral input on the LED driver.
Connect line from the 120 V power source to the L pigtail on the ZEN54

COMPLETE INSTALLATION

Secure your Z-Wave 0-10 V Dimmer and the wall switch in the box with mounting screws, handling the wires with care. Install the wall plate and restore power to the circuit.

INSTALLATION TIPS

The 0-10 V Dimmer adds Z-Wave control to your existing 0-10 V LED driver. It cannot be connected to any other type of fixture or appliance. In most cases, you will have power coming into the wall switch and a load connection between the switch and the LED driver. To accommodate the wiring requirements of the ZEN54 dimmer, you will need to use that connection to bring power to the ZEN54 installed at the fixture. This will not leave enough wires to connect the ZEN54 dimmer to the wall switch directly. In that case, we would recommend installing any Z-Wave light switch to control the ZEN54 dimmer remotely via Z-Wave. The best Zooz models for this application are the ZEN72 Dimmer (for a classic switch look) or the ZEN32 Scene Controller which comes with programmable buttons you can link to your favorite brightness settings on the LED fixture and trigger them with a single tap. Scan the QR code below to access a page with more wiring scenarios and diagrams.

3-WAY INSTALLATIONS

You can install the 0-10 V dimmer in a 3-way set-up using simple on/off or momentary switches: ZEN54 0-10 V Dimmer Wiring Diagrams

Z-WAVE CONTROL

There are 2 methods to add the relay to your hub:

SmartStart:

DO NOT POWER ON THE DEVICE YET.
Use the hub UI / app to scan the SmartStart code on the device. The SmartStart QR code / security PIN is located on the back of the dimmer.
Once completed, power the device for SmartStart inclusion, it will be added automatically.
Do NOT press the Z-Wave® button. (Except for SmartThings, you may need to tap the Z-Wave® button 3 times). See below for QR codes to hub-specific instructions.

Manual Inclusion:

Initiate inclusion (pairing) in the app or hub UI.
Make sure the device is powered and finalize the inclusion at the relay: tap the Z-Wave® button 3 times quickly.
The LED indicator will blink green rapidly to signal communication and turn green for 2 seconds if inclusion is successful or turn red for 2 seconds if the pairing attempt fails. If the LED is not blinking rapidly, you did not click the button fast enough.

How to Add the ZEN54 0-10V Dimmer to Home Assistant

How to Add the ZEN54 0-10V Dimmer to HomeSeer

How to Add the ZEN54 0-10V Dimmer to Hubitat

How to Add the ZEN54 0-10V Dimmer to SmartThings

How to Add the ZEN54 0-10V Dimmer to Z-Box

How to Add the ZEN54 0-10V Dimmer to My Z-Wave Hub

TROUBLESHOOTING

The device won’t add to your system? Try this:

Initiate EXCLUSION and click the Z-Wave button 3 times quickly.
Factory reset the device
Bring the gateway controller (hub) closer to the device, it may be out of range.
Get troubleshooting tips for your hub at www.support.getzooz.com

EXCLUSION (REMOVING / UNPAIRING DEVICE)

Bring your Z-Wave hub close to the device if possible
Put the Z-Wave hub into exclusion mode (not sure how to do that? [email protected])
Click the Z-Wave button on the device 3 times quickly (the LED indicator will start blinking green)
Your hub will confirm exclusion, the LED indicator on the device will turn green for 2 seconds, and the ZEN54 will disappear from your controller's device list.

Can't Add My ZEN54 0-10V Dimmer to Home Assistant

Can't Add My ZEN54 0-10V Dimmer to HomeSeer

Can't Add My ZEN54 0-10V Dimmer to Hubitat

Can't Add My ZEN54 0-10V Dimmer to SmartThings

Can't Add My ZEN54 0-10V Dimmer to Z-Box

Can't Add My ZEN54 0-10V Dimmer to My Z-Wave Hub

FACTORY RESET

If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the ZEN54, click the Z-Wave button once and immediately aer, press and hold it down for 15 seconds. The LED indicator will flash red during the process and turn solid red for 3 seconds to confirm successful reset. NOTE: All previously recorded activity and custom settings will be erased from the device’s memory

ADVANCED SETTINGS

Here are all of the advanced settings for the device: ZEN54 0-10V Dimmer Advanced Settings

How to Access the Advanced Settings for the ZEN54 0-10V Dimmer on Home Assistant

How to Access the Advanced Settings for the ZEN54 0-10V Dimmer on HomeSeer

How to Access the Advanced Settings for the ZEN54 0-10V Dimmer on Hubitat

How to Access the Advanced Settings for the ZEN54 0-10V Dimmer on SmartThings

How to Access the Advanced Settings for the ZEN54 0-10V Dimmer on Z-Box

ASSOCIATION

This 0-10 V Dimmer supports Group 1 with up to 5 devices for Lifeline Group communication and Groups 2-4 with up to 5 devices. This device will send BASIC REPORT and SWITCH MULTILEVEL REPORT to Group 1, BASIC SET command to group 2, SWITCH MULTILEVEL SET to Group 3, and SWITCH MULTILEVEL START LEVEL CHANGE / SWITCH MULTILEVEL STOP LEVEL CHANGE to Group 4 when operated manually from the wall switch. You can set direct association to have the dimmer control another Z-Wave device independently of the hub by using Group 2. Not every hub exposes direct association settings in the interface so please go to www.support.getzooz.com to see if your system allows for direct association.

S2

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. This product features the latest Security 2 (S2) framework to remove smart home network hacking risks. This device is equipped with a unique authentication code for trusted wireless communication

ETL CERTIFICATION

WARNING

This product should be installed indoors upon completion of any building renovations. Ÿ Prior to installation, the device should be stored in a dry, dustand-mold-proof place. Ÿ Do not install the device in a place with direct sun exposure, high temperature, or humidity. Ÿ Keep away from chemicals, water, and dust. Ÿ Ensure the device is never close to any heat source or open flame to prevent fire. Ÿ Ensure the device is connected to an electric power source that does not exceed the maximum load power. Ÿ No part of the device may be replaced or repaired by the user.

WARRANTY

This product is covered under a 1-year limited warranty and extender 5-year warranty once registered. To read the full warranty policy or file a warranty claim, please go to www.getzooz.com/warranty.

IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ'S LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT ZOOZ'S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ'S DELIVERY, OR THE DATE FIXED FOR DELI-VERY IN THE EVENT OF NONDELIVERY.

FCC NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any given installation. If this equipment causes harmful interference to radio or television reception, the user may try to correct the interference by taking one or more of the following measures:

Reorient or relocate receiving antenna
Increase the separation between equipment and receiver
Connect equipment into a separate outlet or circuit from receiver
Consult the dealer or an experienced radio/TV technician for additional assistance