Here is a full list of advanced settings (parameters) for the ZEN54 0-10 V Dimmer.
Some parameters were added in later firmware updates so please make sure you're on the latest firmware to have all of the settings below available. You can view the change log for the ZEN54 here.
On / Off Status After Power Failure
Parameter 1: Set the on/off status and brightness for the dimmer after power failure.
Values: 0 – always off once restored; 1-99 – always on to set brightness once restored; 100 – remembers and restores status and brightness. Default: 100.
Size: 1 byte dec
LED Indicator
Parameter 2: Enable or disable the LED indicator to reflect the current on/off status of the connected load (LED on when the load is on, LED off when the load is off).
Values: 0 – LED always off 1 – LED on when load on, LED off when load off. Default: 1.
Size: 1 byte dec
Dimming Speed
Parameter 3: Set the number of seconds it takes to get from 0% to 100% brightness when pressing and holding the paddle on the wall switch.
Values: 1 – 99 (seconds). Default: 5.
Size: 2 byte dec
Minimum Brightness
Parameter 4: Set the minimum brightness level (in %) for your dimmer. You won’t be able to dim the light below the set value.
Values: 1 – 45 (%). Default: 1.
Size: 1 byte dec
Maximum Brightness
Parameter 5: Set the maximum brightness level (in %) for your dimmer. You won’t be able to add brightness to the light beyond the set value.
Values: 55 – 99 (%). Default: 99.
Size: 1 byte dec
Kickstart Brightness Level
Parameter 6: Set the kickstart brightness level (%) for your dimmer. Use for fixtures that won't turn on when starting from a low brightness level.
Values: 0 – Disabled; 1 – 99 (%). Default: 0.
Size: 1 byte dec
Inclusion From Switch
Parameter 7: Enable or disable ZEN54 inclusion/exclusion via 3 quick toggles (up-down sequences) of the connected wall switch.
Values: 0 – Disable inclusion from switch; 1 – Enable inclusion from switch. Default: 1.
Size: 1 byte dec
Auto Turn-Off Timer
Parameter 8: Auto-off timer will automatically turn the dimmer off after x seconds or minutes (unit set in parameter 10) once it has been turned on.
Values: 0 – timer disabled; 1 – 4294967295. Default: 0.
Size: 4 byte dec
Auto Turn-On Timer
Parameter 9: Auto-on timer will automatically turn the dimmer on after x seconds or minutes (unit set in parameter 10) once it has been turned off.
Values: 0 – timer disabled; 1 – 4294967295. Default: 0.
Size: 4 byte dec
Timer Unit
Parameter 10: Choose between seconds and minutes as the unit for the timers in parameters 8 and 9.
Values: 1 – minutes; 2 – seconds. Default: 1.
Size: 1 byte dec
Load Control (Smart Bulb Mode)
Parameter 11: Enable or disable physical and Z-Wave on/off control. Disable both for smart bulbs.
Values: 0 – Disable control from switch and button; 1 – Enable switch, button, and Z-Wave control; 2 – Disable switch, button, and Z-Wave control. Default: 1.
Size: 1 byte dec
Switch Type
Parameter 12: Choose the wall switch type you want to connect to the dimmer.
Values: 0 – toggle switch (state changes whenever the switch is toggled); 1 – momentary push button; 2 – toggle switch (light on when the switch is toggled up, light off when the switch is toggled down). Default: 2.
Size: 1 byte dec
Status Report Type
Parameter 13: Choose physical (wall switch) and Z-Wave triggers for the dimmer to send a status change report to the hub.
Values: 0 – Switch Multilevel reports for Z-Wave control and Basic Reports for wall switch control; 1 – Switch Multilevel reports for both Z-Wave and wall switch control. Default: 1.
Size: 1 byte dec
Dimmer Off Behavior
Parameter 14: Choose whether the dimmer fully cuts power to 0-10V drivers when off to prevent light glow (applies to selected 0-10V fixtures).
Values: 0 – Keep the power on to the LED driver when the 0-10 V Dimmer is off; 1 – Cut the power off to the LED driver when the 0-10 V Dimmer is off. Default: 1.
Size: 1 byte dec
Physical Ramp Rate ON
Parameter 15: Adjust the ramp rate ON for your dimmer when the button paddle on the wall switch is pressed for a smooth fade-in effect (in seconds).
Values: 0 – instant on; 1- 99 seconds. Default: 5.
Size: 1 byte dec
Physical Ramp Rate OFF
Parameter 16: Adjust the ramp rate OFF for your dimmer when the button paddle on the wall switch is pressed for a smooth fade-out effect (in seconds).
Values: 0 – instant off; 1- 99 seconds. Default: 5.
Size: 1 byte dec
Z-Wave Ramp Rate ON
Parameter 17: Adjust the ramp rate ON for your dimmer when controlled with Z-Wave for a smooth fade-in effect (in seconds).
Values: 0 – instant on; 1- 99 seconds; 100 – match physical. Default: 100.
Size: 1 byte dec
Z-Wave Ramp Rate OFF
Parameter 18: Adjust the ramp rate OFF for your dimmer when controlled with Z-Wave for a smooth fade-out effect (in seconds).
Values: 0 – instant off; 1- 99 seconds; 100 – match physical. Default: 100.
Size: 1 byte dec
Custom Brightness On
Parameter 19: Set the custom brightness level you want the dimmer to come on to (instead of last brightness level).
Values: 0 - last brightness level; 1-99 (%). Default: 0.
Size: 1 byte dec
How to Access the Advanced Settings
How to Access the Advanced Settings for the ZEN54 on Home Assistant
How to Access the Advanced Settings for the ZEN54 on HomeSeer
How to Access the Advanced Settings for the ZEN54 on Hubitat
How to Access the Advanced Settings for the ZEN54 on SmartThings
How to Access the Advanced Settings for the ZEN54 on Z-Box
Manual Control from the Z-Wave Button
3 x tap: enter inclusion (pairing) or exclusion mode
2 x tap and hold (the third time) for 15 seconds: factory reset
Supported Command Classes
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_SECURITY_2_V1
COMMAND_CLASS_SUPERVISION_V1
COMMAND_CLASS_APPLICATION_STATUS_V1
COMMAND_CLASS_BASIC_V2
COMMAND_CLASS_SWITCH_MULTILEVEL _V4
COMMAND_CLASS_CONFIGURATION_V4
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
COMMAND_CLASS_VERSION_V3
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_INDICATOR_V3
The ZEN54 0-10 V Dimmer can be updated via OTA firmware updates, here is how to do that. You can access all firmware files here. Questions? Just reach out to our support!
