Here is a full list of advanced settings (parameters) for the ZEN25 Double Plug firmware 2.0:
On/Off Status Recovery After Power Failure
Parameter 1: Choose the recovery state for your Double Plug’s outlets if power outage occurs.
Values:
0 – Double Plug remembers the status for each outlet prior to power outage and turns back to it (default);
1 – Double Plug automatically turns ON for each outlet once power is restored (it does not remember the status prior to power outage);
2 – Double Plug automatically turns OFF each outlet once power is restored (it does not remember the status prior to power outage);
Size: 1 byte dec.
Power Wattage Report Value Threshold
Parameter 2: Choose how you want your Double Plug to report power consumption to your hub. The number entered as value corresponds to the number of Watts the appliance needs to go over for the change to be reported. So if 5 Watts are entered by default, the Double Plug will report any change in power usage over 5 Watts for each outlet (whether it’s at least 5 Watts more or 5 Watts less compared to previous report).
Values: 0 – 65535. 0 – disabled (Double Plug will not report power consumption based on this setting). Default set to 10.
Size: 4 byte dec.
Power Wattage Report Frequency
Parameter 3: The number entered as value corresponds to the number of seconds. So if 30 is entered by default, the Double Plug will report power consumption (Wattage) every 30 seconds.
Values: 30 – 2678400. Default set to 30.
Size: 4 byte dec.
Energy (kWh) Report Frequency
Parameter 4: Choose how often you want your Double Plug to report power consumption (W) to your controller (hub). The number entered as value corresponds to the number of seconds. So if 300 is entered by default, the Double Plug will report energy usage every 300 seconds (5 minutes).
Values: 30 – 2678400. Default set to 300.
Size: 4 byte dec.
Voltage (V) Report Frequency
Parameter 5: Choose how often you want your Double Plug to report voltage to your controller (hub). The number entered as value corresponds to the number of seconds. So if 300 is entered by default, the Double Plug will report voltage every 300 seconds (5 minutes).
Values: 30 – 2678400. Default set to 300.
Size: 4 byte dec.
Electrical Current (A) Report Frequency
Parameter 6: Choose how often you want your Double Plug to report electrical current (A) to your controller (hub). The number entered as value corresponds to the number of seconds. So if 300 is entered by default, the Double Plug will report current every 300 seconds (5 minutes).
Values: 30 – 2678400. Default set to 300.
Size: 4 byte dec.
Overload Protection
Parameter 7: Set the amp level for overload protection to kick in. The number entered as the value corresponds to the total number of amps the Double Plug needs to detect across both outlets to turn off automatically and send a notification to the hub and associated devices.
Values: 1 – 10 (A). Default set to 10 A.
Size: 1 byte dec.
Auto Turn-Off Timer
Parameter 8: Use this parameter to enable or disable the auto turn-off timer for the left (CH1) outlet. If this feature is enabled, the device connected to CH1 outlet will automatically turn off after a fixed period of time from being turned on (set in parameter 9).
Values: 0 – timer disabled (default); 1 – timer enabled;
Size: 1 byte dec.
Parameter 9: Use this parameter to set the time after which you want the device connected to the left (CH1) outlet to automatically turn off once it
has been turned on. The number entered as value corresponds to the number of minutes.
Values: 1 – 65535 (minutes). Default set to 60 (minutes).
Size: 4 byte dec.
Parameter 12: Enable or disable the auto turn-off timer for the right (CH2) outlet.
Values: 0 – timer disabled (default); 1 – timer enabled;
Size: 1 byte dec.
Parameter 13: Set the time after which you want the device connected to the right (CH2) outlet to automatically turn off once it’s been turned on.
Values: 1 – 65535 (minutes). Default set to 60 (minutes).
Size: 4 byte dec.
Auto Turn-On Timer
Parameter 10: Use this parameter to enable or disable the auto turn-on timer for the left (CH1) outlet. If this feature is enabled, the device connected to left outlet will automatically turn on after a fixed period of time from being turned off (set in parameter 11).
Values: 0 – timer disabled (default); 1 – timer enabled;
Size: 1 byte dec.
Parameter 11: Use this parameter to set the time after which you want the device connected to the left (CH1) outlet to automatically turn on once it has been turned off. The number entered as value corresponds to the number of minutes.
Values: 1 – 65535 (minutes). Default set to 60 (minutes).
Size: 4 byte dec.
Parameter 14: Enable or disable the auto turn-on timer for the right (CH2) outlet.
Values: 0 – timer disabled (default); 1 – timer enabled;
Size: 1 byte dec.
Parameter 15: Set the time after which you want the device connected to the right outlet to automatically turn on once it has been turned off.
Values: 1 – 65535 (minutes). Default set to 60 (minutes).
Size: 4 byte dec.
Manual Control
Parameter 16: Choose if you want to use the Z-Wave button on the Double Plug to turn the outlets on or off manually or if you want to disable this function. If this parameter is set to 0 (disabled), you will only be able to turn any of the outlets on or off remotely using your Z-Wave gateway controller.
Values:
0 – manual control disabled for both outlets;
1 – manual control enabled for both outlets (default).
Size: 1 byte dec.
LED Indicator Mode
Parameter 17: Choose if you want the LED indicators next to each outlet to come on when power is on or off, or if you want to disable them.
Values:
0 – LED indicator will display power consumption whenever the device is plugged in (LED stays on at all times, even if the plug is off);
1 – LED indicator will display power consumption whenever the device is ON in and will turn off when the plug is OFF (default);
2 – LED indicator will display the level of power consumption for 5 seconds only whenever the device is turned on or off (LED indicator will stay off for most of the time);
3 – LED indicator is OFF at all times except for inclusion, exclusion, and Z-Wave range test.
Size: 1 byte dec.
Note: You can also switch between the LED indicator modes by clicking the Z-Wave button 6 times quickly.
Disable Energy Reports
Parameter 18: Choose if you want the plug to report power use or on/off activity in the USB port to the hub.
Values:
0 – energy and USB reports enabled (default);
1 – energy and USB reports disabled;
2 – energy reports for left outlet disabled;
3 – energy reports for right outlet disabled;
4 – USB reports disabled. Size: 1 byte dec.
Size: 1 byte dec.
Note: You can also switch between the LED indicator modes by clicking the Z-Wave button 6 times quickly.
How to Access the Advanced Settings:
Looking for a firmware update? Once you register your product and create an account in our support portal, you'll be able to access all firmware files here. Questions? Feel free to reach out to our customer service team, we reply 7 days a week!
