ZSE44 Temperature | Humidity Sensor Product Manual

Don't forget to register your product for extended warranty and more perks:

Click here to register your device here.

FEATURES

Monitor temperature and humidity via Z-Wave
NEW 800 series chip for faster communication and more battery life than ever
Z-Wave Long Range for ultra reliable no-mesh communication
Snap-in mounting bracket
Powered by a single coin battery
The latest S2 security and SmartStart for secure set-up
Supports OTA firmware updates

SPECIFICATIONS

Model Number: ZSE44 800LR
Power: 1 x CR2450 battery
Operating Temperature: 40°-90° F
Dimensions: 2.2” x 1.3” x 0.2”
Range: Up to 150 feet (up to 1300 with Long Range) line of sight
Installation and Use: Indoor or outdoor under eve (can’t be exposed to direct rainfall or sun, a little splash is OK)

INSTALLATION

POWER ON THE SENSOR: Choose your inclusion method first!

If you are including the sensor via SmartStart or Z-Wave Long Range, it is very important not to power on the sensor until you have completed the SmartStart process in your hub UI (see instructions below). If you are including manually to the classic mesh network, you will need to power on the sensor before including it to your hub.

Use the triangle tool to gently open the sensor’s cover and access the battery. Pull the tab from under the battery to activate the sensor. Don’t close the cover just yet. The LED indicator will start blinking for around 10 seconds once the sensor is powered.

The LED indicator doesn’t blink or light up at all?

Make sure the battery is inserted correctly per the positive / negative pole marks.
Try a fresh lithium nonrechargeable battery.
Click the Z-Wave button 3 times as quickly as possible to force inclusion/exclusion mode in case you missed when it first flashed.

Z-WAVE CONTROL

There are 2 methods to add the dimmer to your hub:

1. SmartStart:

DO NOT POWER ON THE DEVICE YET.
Use the hub UI / app to scan the SmartStart code on the device. The SmartStart QR code / security PIN is on the inside of the sensor’s battery cover.
Once completed, power the device for SmartStart inclusion, it will be added automatically (see above for instructions to power the sensor).
Do NOT press the Z-Wave® button. (Except for SmartThings, you may need to tap the Z-Wave® button 3 times). See below for QR codes to hub-specific instructions.

2. Manual Inclusion:

Initiate inclusion (pairing) in the app or hub UI.
Make sure the device is powered and finalize the inclusion at the dimmer: tap the Z-Wave® button 3 times quickly.
The LED indicator will blink green to signal communication and turn green for 2 seconds if inclusion is successful or turn red for 2 seconds if the pairing attempt fails.

It’s best to add your sensor from the area where it will be installed so the hub can find the best route to reach it right away.

How to Add the ZSE44 Temperature | Humidity Sensor to Home Assistant

How to Add the ZSE44 Temperature | Humidity Sensor to HomeSeer

How to Add the ZSE44 Temperature | Humidity Sensor to Hubitat

How to Add the ZSE44 Temperature | Humidity Sensor to SmartThings

How to Add the ZSE44 Temperature | Humidity Sensor to Z-Box

TROUBLESHOOTING

The sensor won’t add to your system? Try this:

Initiate EXCLUSION in your hub and click the Z-Wave button 3 times as quickly as possible.
Click the Z-Wave button quicker when adding it.
Bring the sensor closer to your hub, it may be out of range.
Double-check if the device is powered. 5. Get troubleshooting tips specific to your hub at www.support.getzooz.com

EXCLUSION

Bring the sensor within direct range of your Z-Wave hub.
Put the Z-Wave hub into exclusion mode (see below for hub instructions).
Click the Z-Wave button 3 times as quickly as possible.
Your hub will confirm exclusion and the sensor will disappear from your controller's device list

Can't Add My ZSE44 Temperature | Humidity Sensor to Home Assistant

Can't Add My ZSE44 Temperature | Humidity Sensor to HomeSeer

Can't Add My ZSE44 Temperature | Humidity Sensor to Hubitat

Can't Add My ZSE44 Temperature | Humidity Sensor to SmartThings

Can't Add My ZSE44 Temperature | Humidity Sensor to Z-Box

FACTORY RESET

When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process:

Make sure the sensor is powered
Click the Z-Wave button twice and hold it the third time for 10 seconds.
The LED indicator will blink continuously.
Immediately after, click the ZWave button twice more to finalize the reset.
The LED indicator will flash 3 times to confirm a successful reset.

NOTE: All previously recorded activity and custom settings will be erased from the device’s memory.

WAKE-UP MODE

The sensor’s wake-up interval is set to 12 hours by default to save battery life. Use the Wake Up Command Class to adjust the interval. Click the Z-Wave button 4 times quickly to wake the sensor up manually. The LED indicator will flash once to confirm the device is awake. During wake-up, the sensor turns the Z-Wave radio on for one minute to receive communication from the hub. Long wake-up interval will not affect how oen the sensor reports to your hub so we recommend leaving the default setting to conserve battery.

BATTERY POWER TIP

This sensor runs on a coin battery with smaller capacity than the lithium CR batteries used in other sensors so you may see the battery readings fluctuate from low to higher readings when the sensor is awake during programming and testing. The battery will usually go back to its stable reading within a few hours so always allow a day or two aer you see the first lower reading before checking on the actual battery life left for your device.

ASSOCIATION

The XS Sensor supports Group 1 for Lifeline communication and Groups 2-5 with up to 5 devices per group for basic on/off control. Use Group 2 for high temperature alerts; Group 3 for low temperature alerts; Group 4 for high humidity alerts; and Group 5 for low humidity alerts. See parameters 5-8 to set the thresholds. Please note that not all Z-Wave systems give users access to direct association settings so if you’re note sure where to find it, please get in touch with our support and we’ll be happy to help.

ADVANCED SETTINGS

Click the Z-Wave button 4 times quickly to wake the sensor up after updating any of the settings.

ZSE44 Temperature | Humidity Sensor Advanced Settings

How to Access the Advanced Settings for the ZSE44 Temperature | Humidity Sensor on Home Assistant

How to Access the Advanced Settings for the ZSE44 Temperature | Humidity Sensor on HomeSeer

How to Access the Advanced Settings for the ZSE44 Temperature | Humidity Sensor on Hubitat

How to Access the Advanced Settings for the ZSE44 Temperature | Humidity Sensor on SmartThings

How to Access the Advanced Settings for the ZSE44 Temperature | Humidity Sensor on Z-Box

INDOOR MOUNTING

We recommend including your sensor to the Z-Wave network from the location you want to install it before you actually mount it.
Place the sensor on a dry and clean surface in the space you’d like to monitor temperature and humidity. Use the supplied adhesive tape to fix the sensor to the surface, with the battery slot and sensor perforation pointing down.
Test the sensor overnight to make sure it’s reporting both temperature and humidity according to the settings. It may take up to 48 hours to adjust to the environment so give it a couple of days before evaluating the reports.

OUTDOOR MOUNTING

Install the product outdoors under eve with the snap-on mounting bracket (included) for best results.
Add the sensor to Z-Wave from the area where it will be installed before mounting it.
Use the supplied screws to fix the mounting bracket to a dry clean surface around the spot you’d like to monitor.
Insert the sensor into the bracket, it should snap right on. Remember to position the device so that the sensor perforation is pointing down.

S2

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. This product features the latest Security 2 (S2) framework to remove smart home network hacking risks. This device is equip-ped with a unique authentification code for trusted wireless communication.

WARNING

This product should be installed indoors or outdoors under eve upon completion of any building renovations.
Prior to installation, the device should be stored in a dry, dust-and-moldproof place.
Do not install the device in a place with direct sun exposure, high temperature, or humidity.
Keep away from chemicals, water, and dust.
Ensure the device is never close to any heat source or open flame to prevent fire.
No part of the device may be replaced or repaired by the user except for the batteries.

WARRANTY

This product is covered under a 12- month limited warranty and 5-year extended warranty once registered. To read the full warranty policy, register your product, or file a warranty claim, please go to ww.getzooz.com/warranty,

IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ'S LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT ZOOZ'S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT POR-TION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ'S DELIVERY, OR THE DATE FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY.

FCC NOTE

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any given installation. If this equipment causes harmful interference to radio or television reception, the user may try to correct the interference by taking one or more of the following measures:

Reorient or relocate receiving antenna
Increase the separation between equipment and receiver
Connect equipment into a separate outlet or circuit from receiver
Consult the dealer or an experienced radio/TV technician for additional assistance

All brand names displayed are trademarks of their respective holders.