Here is a full list of advanced settings (parameters) for the ZSE70 Outdoor Motion Sensor.
Motion Sensitivity
Parameter 1: Set motion sensitivity for the motion detector to minimize false alerts.
Values: 0 – disable motion reports; 1 – 8 where 8 is the most sensitive and 1 is the least sensitive. Default: 6.
Size: 1 byte dec
Motion Clear Delay
Parameter 2: The amount of time the device waits to send a motion clear notification after the last motion event is detected.
Values: 10-3600 seconds. Default: 30.
Size: 2 bytes dec
Basic Set Reporting
Parameter 3: Basic set values sent by the sensor for motion / no-motion events sent to associated devices.
Values: 0 － Disable Basic Set Reports; 1 － Basic Set 0xFF For Motion / Basic Set 0x00 For No Motion; 2 － Basic Set 0x00 For Motion / Basic Set 0xFF For No Motion; 3 － Basic Set 0xFF For Motion / No Reports For No Motion; 4 － Basic Set 0x00 For Motion / No Reports For No Motion; 5 － No Reports For Motion / Basic Set 0x00 For No Motion; 6 － No Reports For Motion / Basic Set 0xFF For No Motion; 7 － Custom Report For Motion / Custom Report For No Motion (set in par 4). Default: 7.
Size: 1 byte dec
Custom Basic Set Reports
Parameter 4: High byte is the value sent when motion is detected, low byte is the value sent when motion is cleared. e.g：0x0A00 means: When motion is detected, Send Basic Set(0A), When motion is cleared, send Basic Set(00).
Values: Configurable values. Default: 65280.
Size: 2 bytes dec
Temperature Report Unit
Parameter 5: Set the temperature report unit.
Values: 0 - Celsius; 1 - Fahrenheit. Default: 1.
Size: 1 byte dec
LED for Motion
Parameter 6: Decide whether you want the LED indicator to light up when motion is detected or not.
Values: 0 – LED Off; 1 – LED On. Default: 1.
Size: 1 bytes dec
Low Battery Alert
Parameter 7: Set the low battery threshold to receive an alert when battery is running low.
Values: 10-50 %. Default: 10.
Size: 1 byte dec
Battery Check Frequency
Parameter 8: Set how often you want the device to check battery power for changes (this is not a reporting frequency setting).
Values: 0 - Disable (the device won't check for battery power changes and won't send reports to the hub); 1 - 744 hours. Default: 4.
Size: 1 byte dec
Temperature Check Frequency
Parameter 9: Set how often you want the device to check ambient temperature for changes (this is not a reporting frequency setting).
Values: 0 - Disable (the device won't check for temperature changes and won't send temperature reports to the hub); 1 - 600 seconds. Default: 20.
Size: 2 byte dec
Lux Check Frequency
Parameter 10: Set how often you want the device to check lux level for changes (this is not a reporting frequency setting).
Values: 0 - Disable (the device won't check for lux changes and won't send lux reports to the hub); 1 - 600 seconds. Default: 10.
Size: 2 byte dec
Battery Reporting Threshold
Parameter 11: Set when you want the device to send battery reports. This setting specifies the amount of % change the battery needs to record in order for the device to send a new battery report to the hub.
Values: 0 - Ignore (the device won't send battery reports to the hub); 1 - 50 %. Default: 2.
Size: 1 byte dec
Temperature Reporting Threshold
Parameter 12: Set when you want the device to send temperature reports. This setting specifies the amount of F degree change the sensor needs to record in order for the device to send a new temperature report to the hub.
Values: 0 - Ignore (the device won't send temperature reports to the hub); 1 - 144. Default: 1.
Size: 1 byte dec
Lux Reporting Threshold
Parameter 13: Set when you want the device to send lux level reports. This setting specifies the amount of lux change the sensor needs to record in order for the device to send a new lux level report to the hub.
Values: 0 - Ignore (the device won't send lux reports to the hub); 1 - 30000. Default: 50.
Size: 2 byte dec
Temperature Offset
Parameter 14: Set the temperature reporting offset. Value 100 is zero offset; values 0-99 decrease the value (ex: 56 means deduct 4.4 degrees from the measured value); values 101-200 increase the value (ex: value 121 means add 2.1 degree to the reported value). NOTE: Device must be factory reset to restore this value to default.
Values: 0 – 200. Default: 100 (no offset).
Size: 1 byte dec
Lux Offset
Parameter 15: Set the lux reporting offset. Value 100 is zero offset; values 0-99 decrease the value (ex: 75 means deduct 25 lux from the measured value); values 101-200 increase the value (ex: value 147 means add 47 lux to the measured value). NOTE: Device must be factory reset to restore this value to default.
Values: 0 – 200. Default: 100 (no offset).
Size: 1 byte dec
Lux Level Trigger
Parameter 16: Set the lux level trigger. If brightness level is lower than the set lux value, the sensor will send a motion event notification to the hub.
Values: 0 – Ignore (motion always reported when detected); 1 - 30000 lux (motion reports will only be sent if lux level is lower than the set value). Default: 0.
Size: 2 byte dec
Temperature Reporting Frequency
Parameter 17: Set the reporting interval for temperature. Values 1-43200 will send a report regardless of the threshold value selected in parameter 12.
Values: 0 – Ignore, reports based on threshold only (value set in parameter 12). 1 - 43200 seconds. Default: 0.
Size: 2 byte dec
Lux Reporting Frequency
Parameter 18: Set the reporting interval for lux level. Values 1-43200 will send a report regardless of the threshold value selected in parameter 13.
Values: 0 – Ignore, reports based on threshold only (value set in parameter 13). 1 - 43200 seconds. Default: 0.
Size: 2 byte dec
How to Access the Advanced Settings
How to Access the Advanced Settings for the ZSE70 on Home Assistant
How to Access the Advanced Settings for the ZSE70 on HomeSeer
How to Access the Advanced Settings for the ZSE70 on Hubitat
How to Access the Advanced Settings for the ZSE70 on SmartThings
How to Access the Advanced Settings for the ZSE70 on Z-Box
The Outdoor Motion Sensor can be updated via OTA firmware updates, here is how to do that. You can access all firmware files here. Remember to register your product and create an account here for extended warranty and priority troubleshooting. Questions? Just reach out to our support!
