You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close
Looking for Z-Box Hub Support? Please click here to access the Z-Box Hub Support Portal.
announcement close button
Home > Security Sensors & Sirens > ZSE11 Q Sensor > ZSE11 Q Sensor Advanced Settings
ZSE11 Q Sensor Advanced Settings
print icon

Here is a full list of advanced settings (parameters) for the ZSE11 Q Sensor on firmware 1.30:

Motion Sensor

Parameter 12: Set motion sensitivity for the motion detector to minimize false alerts.

Values: 0 – disable motion reports; 1 – 8 where 8 is the most sensitive and 1 is the least sensitive. Default: 6.

Size: 1 byte dec

 

Parameter 13: Set motion clear time for the delay before the sensor reports no motion to the hub and associated devices after detecting the last motion activity.

Values: 10 - 3600 (seconds). Default: 30.

Size: 2 byte dec

 

Parameter 14: Enable or disable basic set reporting when motion is detected.

Values: 0 – don’t send basic set reports when motion is detected; 1 – send basic set reports when motion is detected (default).

Size: 1 byte dec

 

Parameter 15: Select the basic set value to be sent when motion is detected.

Values: 0 – send 0xFF basic set report (ON) when motion is detected (default); 1 – send 0x00 basic set report (OFF) when motion is detected.

Size: 1 byte dec

 

Parameter 16: Enable or disable binary sensor reports when motion is detected.

Values: 0 – don’t send binary sensor reports when motion is detected; 1 – send binary sensor reports when motion is detected (default).

Size: 1 byte dec

 

Parameter 19: Enable or disable LED indicator for motion alerts.

Values: 0 – don’t flash LED when motion is detected; 1 – flash LED indicator when motion is detected (default).

Size: 1 byte dec

Temperature Sensor

Parameter 18: Set the temperature unit for your sensor. NOTE: many home automation platforms will automatically adjust the reporting unit for you based on your general platform or device settings which will override this parameter so please make sure you check these settings as well.

Values: 1 – Celsius; 2 – Fahrenheit (default).

Size: 1 byte dec

Low Battery Alert

Parameter 32: Set the % level for the sensor to report low battery to your hub.

Values: 10 - 50 (%). Default: 10.

Size: 1 byte dec

Reporting Frequency

Parameter 172: Set the reporting frequency for battery, temperature, humidity, and light level. This setting is ignored unless the reporting threshold parameters are set to 0. The sensor only reports new readings based on threshold OR frequency, prioritizing the threshold setting. The values entered correspond to the number of hours. Note: Frequent reports will affect battery life.

Values: 1 - 744 (hours). Default: 4 (hours).

Size: 2 byte dec

Reporting Threshold

Parameter 183: Set the reporting threshold for temperature. The sensor will report new temperature value to the hub whenever temperature changes by the number of degrees entered as value. Enter 0 (disabled reporting based on the threshold) if you'd like the sensor to report based on frequency instead.

Values: 0 – disable temperature reporting based on environmental changes; 1 - 144 (degrees Fahrenheit). Default: 1.

Size: 2 byte dec

 

Parameter 184: Set the reporting threshold for humidity. The sensor will report new humidity value to the hub whenever humidity changes by the percentage number entered as value. Enter 0 (disabled reporting based on the threshold) if you'd like the sensor to report based on frequency instead.

Values: 0 – disable humidity reporting based on environmental changes; 1 - 80 (%). Default: 5.

Size: 1 byte dec

 

Parameter 185: Set the reporting threshold for lux. The sensor will report new lux value to the hub whenever the brightness level changes by the number of lux entered as value. Enter 0 (disabled reporting based on the threshold) if you'd like the sensor to report based on frequency instead.

Values: 0 – disable lux reporting based on environmental changes; 2 - 300000 (lux). Default: 50.

Size: 2 byte dec

 

How to Access the Advanced Settings:

SmartThings

Hubitat

Vera

Home Assistant

 

Press and hold the Z-Wave button for 3 seconds to wake the sensor up after updating the settings so they can be immediately received and saved.

Not sure which settings to adjust or where to access the advanced parameters on your hub? Please get in touch and we'll be happy to help!

 

The ZSE11 on firmware 1.10 or higher can be updated via OTA firmware updates, here is how to do that. You can access all firmware files here once you register your product and create an account here. Questions? Please reach out to our support team who's here to help you 7 days a week!

Feedback
0 out of 0 found this helpful

Have you tried our virtual assistant chatbot? This AI tool can help you find answers from thousands of articles in our Knowledge Base quickly. Find it in the bottom righthand corner of the page.

Need more help? Our friendly team is ready to help you with any questions or concerns you may have about Zooz devices. Click here to submit a support ticket.

Are your devices registered? Extended warranty and firmware access is available for registered Zooz customers. Click here to submit your registration form.

Find the latest Zooz devices and great Z-Wave deals at The Smartest House.
 
scroll to top icon