You are using an unsupported browser. Please update your browser to the latest version on or before July 31, 2020.
close
You are viewing the article in preview mode. It is not live at the moment.
Looking for Z-Box Hub Support? Please click here to access the Z-Box Hub Support Portal.
Home > Light Switches > ZEN72 Dimmer > ZEN72 Dimmer Change Log
ZEN72 Dimmer Change Log
print icon

Here is a list of updates we made to the ZEN72 700 Series Dimmer so far:

VER. 1.0 (released 12/2020)

Original release

Firmware: 1.01

  • Central scene triggers for up to 10 scenes or devices

  • Smart bulb mode (disable relay)

  • Support for on/off and momentary switch types in direct 3-way

  • Programmable double and single click behavior

  • Night light mode (press and hold the lower paddle when the dimmer is off to turn on to low brightness)

VER. 10.0 (released 06/2021)

Firmware: 10.0

  • Removed the delay for on/off control from paddle with scene control disabled
  • Added the ability to disable programming function from the paddles (Parameter 26)
  • Fixed relay behavior after power outage in smart bulb mode (both relay and on/off status are restored correctly after an outage now)
  • Fixed night light mode (doesn't activate the light anymore when disabled)
  • Fixed single-tap behavior bug in a 3-way installation (the connected 3-way switch now honors the single-tap setting as well)

VER. 10.20 (released 05/2022 as OTA)

Firmware: 10.20

  • Separated ramp rate settings into 4 new parameters: ramp rate ON physical (9), ramp rate OFF physical (27), ramp rate ON Z-Wave (28), ramp rate OFF Z-Wave (29). See all settings here.
  • Fixed ramp rate settings to honor minimum and maximum brightness settings for both physical and Z-Wave commands.
  • Added association Group 4 for remote dimming.
  • Added parameter 30 to adjust dimming multilevel duration for devices associated with the dimmer in Group 3 and Group 4. See all settings here.
  • Adjusted dimming scale mapping to minimum and maximum brightness levels.
  • Fixed multilevel association to work for both manual and Z-Wave commands.
  • Fixed night light behavior (the dimmer no longer sends central scene events repeatedly when night light mode is disabled and the bottom paddle is held).
  • Fixed smart bulb mode behavior after a power outage: the dimmer now restores both the actual status of the dimmer and the reported status to the hub correctly when in smart bulb mode.

VER. 10.30 (released 09/2022 as OTA)

Firmware: 10.30

  • Adjusted Direct Association behavior for Group 3 for full sync and smooth dimming when two or more Z-Wave dimmers are associated together in a virtual 3-way or 4-way set-up
  • The value for the double tap setting now applies to devices associated with the Z-Wave dimmer in Groups 2-4
  • The Night Light Mode setting now applies to devices associated with the Z-Wave dimmer in Groups 2-4
  • Added parameter 7 to choose Direct Association reports sent to devices associated with the Z-Wave dimmer in Group 3. See all settings here.

VER. 10.40 (released 05/2023 as OTA)

Firmware: 10.40

  • Fixed central scene bug for control of its own load in smart bulb mode
  • Added parameter 31 to enable scene control from the momentary switch in a 3-way. See all settings here.
  • Added parameter 32 to disable LED blinking when a setting is changed. See all settings here
  • Changed the manual operation for disabling the relay (smart bulb mode): Hold the UPPER paddle for 10 seconds until the LED indicator starts blinking, then within 2 seconds, tap the upper paddle 5 times quickly to change this mode. The LED indicator will stay solid green for 3 seconds to confirm the change.
  • Improved the factory reset procedure: The dimmer will not lock up if the factory reset is not successful in certain scenarios. 

VER. 2.0 (06/2022)

Hardware: 2.0

  • Updated the Voltage regulator to improve surge protection

Firmware: 2.0

  • Based on the 10.20 OTA changes (see above)

VER. 2.10 (09/2022)

Firmware: 2.10

  • Based on the 10.30 OTA changes (see above)

VER. 2.20 (05/2022)

Firmware: 2.20

  • Based on the 10.40 OTA changes (see above)

VER. 800LR (released 05/2023)

Hardware: 3.0

  • 800 Series Z-Wave chip

Firmware: 3.10

  • Based on 10.40 firmware (see above)
  • Long Range ready

Firmware: 3.20 (released 07/2023 as OTA)

  • Improved the dimming experience for selected light fixtures/bulbs.
  • Fixed the inclusion issues on the HomeSeer platform.
  • Addressed issues with the dimmer occasionally showing offline or becoming unresponsive on select platforms.

Firmware: 3.30 (released 09/2023 as OTA)

  • Improved Direct Association Group 3 for the multilevel set functionality. 

 

Your ZEN72 700 Series Dimmer can be updated via OTA firmware updates, you can access all firmware files here once you register your product and create an account here. Questions? Just reach out to our support!

Feedback
1 out of 1 found this helpful

Have you tried our virtual assistant chatbot? This AI tool can help you find answers from thousands of articles in our Knowledge Base quickly. Find it in the bottom righthand corner of the page.

Need more help? Our friendly team is ready to help you with any questions or concerns you may have about Zooz devices. Click here to submit a support ticket.

Are your devices registered? Extended warranty and firmware access is available for registered Zooz customers. Click here to submit your registration form.

Find the latest Zooz devices and great Z-Wave deals at The Smartest House.
 
scroll to top icon