Here is a full list of advanced settings (parameters) for the ZEN05 Outdoor Smart Plug:
LED Indicator
Parameter 1: Decide how the LED indicator behaves depending on the on/off status of the plug. The LED indicator will flash twice to confirm a setting has been changed.
Values:
0 – LED indicator is on when the plug is on, LED indicator is off when the plug is off (default)
1 – LED indicator is on when the plug is off, LED indicator is off when the plug is on
2 – LED indicator is always off
Size: 1 byte dec
NOTE: Click the Z-Wave button 6 times quickly to toggle between the values of this parameter manually from the device.
Parameter 7: Set the brightness level of the LED indicator.
Values:
0 - high
1 - medium
2 - low (default)
Size: 1 byte dec
NOTE: Click the Z-Wave button 8 times quickly to toggle between the values of this parameter manually from the device.
Auto-off Timer
Parameter 2: Use this parameter to set the auto turn-off timer: the time after which you want the Outdoor Plug to automatically turn off once it has been turned on. The number entered as value corresponds to the number of minutes.
Values: 0 - timer disabled (default); 1-65535 (minutes)
Size: 4 byte dec
Auto-on Timer
Parameter 4: Use this parameter to set the auto turn on timer; the time after which you want the Outdoor Plug to automatically turn on once it has been turned off. The number entered as value corresponds to the number of minutes.
Values: 0 - timer disabled (default); 1-65535 (minutes).
Size: 4 byte dec
On/Off Status Recovery After Power Failure
Parameter 6: Choose the recovery state for your Outdoor Plug if power outage occurs
Values:
0 - Outdoor Plug automatically turns OFF once power is restored (it ignores the status prior to power outage)
1 - Outdoor Plug automatically turns ON once power is restored (it ignores the status prior to the power outage)
2 - Outdoor Plug remembers the status prior to power outage and turns back to it (default)
Size: 1 byte dec
Disable/Enable Manual On/Off Control
Parameter 8: Choose if you want to use the physical Z-Wave button on the plug to turn the outlet on or off manually, or if you want to disable this function. If this parameter is set to 0 (disabled), you will only be able to turn the outlet on or off remotely using your Z-Wave hub.
Values: 0 - manual control disabled; 1 - manual control enabled (default)
Size: 1 byte dec
Manual Control
1 x Z-Wave button press: turn plug ON or OFF
3 x Z-Wave button press: inclusion or exclusion
6 x Z-Wave button press: toggle between Parameter 1 (LED Indicator Control) settings
8 x Z-Wave button press: toggle between Parameter 7 (LED Brightness) settings
Factory Reset: click Z-Wave button 2 twice quickly, then hold it the third time for at least 10 seconds. The LED indicator will flash green 3 times, indicating that the reset is successful.
Association Groups
The Outdoor Plug supports Group 1 for Lifeline communication and Group 2 with up to 5 devices for basic on/off control. This device will send a Basic Set command to Group 2 whenever it changes its on/off status.
Supported Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_SWITCH_BINARY_V2
COMMAND_CLASS_CONFIGURATION_V4
COMMAND_CLASS_ASSOCIATION_V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V4
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_INDICATOR_V3
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
How to Access the Advanced Settings:
SmartThings
Hubitat
Home Assistant
If you'd like to update your ZEN05 Outdoor Plug, please register your device here. Once registered, you'll have access to the firmware updates. Don't forget to double check the model number and current firmware version before installing new firmware. Questions? Reach out to us!