To ensure the device is correctly recognized and for the best user experience, we recommend the community driver for the ZSE50 Siren & Chime on Hubitat.
With the advent of Z-Wave long range (ZWLR), Hubitat now offers the option to include your long range supporting devices via standard Z-Wave mesh or with ZWLR. You can read more here about how the standard mesh and ZWLR differ and decide which is the best method for you.
Standard Mesh Inclusion Options
When including your device to the mesh (using repeaters), you have the option of utilizing SmartStart or a standard manual inclusion. We've included instructions for both methods below:
Smart Start Inclusion
On the Hubitat app:
- DO NOT power on the device at this time; SmartStart must be properly initiated first.
- Open the Tools tab (wrench icon on the bottom)
- Scroll to the bottom, select Z-Wave
- This will take you to a screen where you can select either Smart Start or regular inclusion
- Select Smart Start
- This will take you to the smart start inclusion list. Devices will be displayed there that are in the process of inclusion through Smart Start.
- Select the QR symbol in the top right to open the camera for the DSK scan; scan the QR Code on the back of the device.
- Power the device (important to do this AFTER QR scan) by plugging it into a standard outlet. The LED Indicator will flash yellow once to confirm the device is powered and ready to be included.
- The device integration will begin. The window will appear asking you to name the device; click Save after naming
- Finishing inclusion may take a few minutes
If you have any issues with Smart Start Inclusion on Hubitat, please review this video: https://www.youtube.com/watch?v=Sf-Fldjb0to. The steps should be the same whether you have a C-7 or C-8.
Manual Inclusion
-
Open Hubitat in your Internet browser
-
Go to Devices
-
Click on + Add Device in the top right corner
-
Click on Z-Wave
-
Click on Start Z-Wave Inclusion
-
If you're using a hub that supports S2 security, it may ask you to enter the PIN located on the QR code.
-
While the app says it is in inclusion mode, tap the + button on the device 3 times quickly. The LED indicator will blink green to signal communication and you’ll also hear the message “Device in inclusion mode” to confirm the state.
- The LED indicator will then turn green for 2 seconds announcing audibly “Device added” if the inclusion is successful or turn red for 2 seconds if the pairing attempt fails.
-
Rename and confirm the found device
Z-Wave Long Range (ZWLR) Inclusion
If you want to include the device with ZWLR, first ensure you're using the model C-8 hub or later, with a minimum platform version of 2.3.9 or later in the US region only. You also need to ensure your device model and firmware version support ZWLR.
Next, you'll want to install the SmartStart Manager app. You can read more details on this custom app here, and be sure to thank Jeff for his work on the app!
To include the device as a ZWLR device, Z-Wave SmartStart must be used. Note that all ZWLR devices must support SmartStart, but not all SmartStart devices support ZWLR. SmartStart will still include the device as a traditional Z-Wave node if LR is not supported.
To add a device using SmartStart with ZWLR in Hubitat once the SmartStart Manager app is installed:
- Do NOT power on the device until instructed to do so in step 7.
- Locate the SmartStart QR code for the device. The QR code sticker also contains the numeric DSK (device-specific key) next to it; you will need this later. Do not power on the device at this time.
- For the Hubitat 2.0 mobile app: go to Devices > + (plus icon) > Add SmartStart Devices
- For the current 1.x app --- do not edit the SmartStart entry as LR is not manually selectable at this time) Tools > Z-Wave Tools.
- Select the SmartStart button.
- Select the QR code icon from the top-right (and allow camera access for the app if prompted).
- Scan the QR code for the device that you located in Step 1.
- Provide a name for the device when prompted (to be used on the hub, e.g., "Living Room Dimmer" or "Hallway Motion"; this can be changed on the hub later).
- Power the device (important to do this AFTER QR scan) by plugging it into a standard outlet. The LED Indicator will flash yellow once to confirm the device is powered and ready to be included. The inclusion process should start immediately and the device should be automatically added to your hub.
If the relay is having problems connecting to Hubitat, try the exclusion process first. It will help the ZSE50 configure properly, even if it has never been connected to the hub.
Please let us know if you need any other assistance!
